Metric horsepower to Megawatts Converter
Convert Metric horsepower (PS) to Megawatts (MW) instantly, or use the conversion table below to look up common values.
Metric horsepower to Megawatts conversion table
| Metric horsepower (PS) | Megawatts (MW) |
|---|---|
| 1 | 7.355e-4 |
| 2 | 0.001471 |
| 3 | 0.002206 |
| 4 | 0.002942 |
| 5 | 0.003677 |
| 10 | 0.007355 |
| 25 | 0.018387 |
| 50 | 0.036775 |
| 100 | 0.07355 |
How to convert Metric horsepower to Megawatts
1 PS equals 7.355e-4 MW. Use the converter above for any value, or read the table for common conversions.
MW = PS × 0.0007354987499999999 · PS = MW × 1359.6216173039045Multiply a metric horsepower figure by 7.355e-4 to get megawatts, or divide it by 1,359.621617 to go the other way.
Worked examples
- 1 PS= 7.355e-4 MW
- 5 PS= 0.003677 MW
- 10 PS= 0.007355 MW
- 100 PS= 0.07355 MW
- 500 PS= 0.367749 MW
What these units are
Metric horsepower (PS). Metric horsepower (PS) is 735.49875 watts, used for vehicle engine ratings across much of Europe and Asia. It is slightly smaller than mechanical horsepower.
Megawatts (MW). A megawatt is 1,000 kilowatts. It is used for power stations, industrial loads and grid capacity, where large generator sets run into the megawatts.
Metric power conversions are exact. Check whether a horsepower figure is mechanical or metric before comparing two engines.
Converting Metric horsepower to Megawatts in practice
Reading the result in megawatts
A megawatt is 1,000 kilowatts, or one million watts, and it carries the symbol MW. Power at this scale is quoted in megawatts because a figure in kilowatts would run to several digits.
Grid-scale generating stations, industrial plants, large data centres and utility-scale solar farms are described in megawatts of capacity. Transmission and distribution planning also uses the unit for load forecasts.
A megawatt measures capacity, which is a rate, while a megawatt-hour measures delivered energy. One megawatt sustained for one hour therefore equals one megawatt-hour, or 3.6 gigajoules.
Reporting a plant's output as megawatts when the figure is megawatt-hours confuses capacity with production. The two differ by the operating time, so a megawatt figure alone says nothing about how much energy was generated.
Megawatts describe capacity at grid and industrial scale, while kilowatts describe the appliances and generators on the same site. The unit is also mistaken for the megawatt-hour, which is a sibling in the energy dimension; capacity and delivered energy are not the same figure.
Checking a metric horsepower to megawatts conversion
Within the metric units a power conversion is a power of a thousand: watts to kilowatts, kilowatts to megawatts, and back. Those pairs are decimal shifts and a reader can do them without a converter.
Anything involving horsepower is a multiplication by a definition rather than a shift, and there are two definitions. Mechanical horsepower is exactly 745.7 watts and metric horsepower exactly 735.49875 watts, so the same engine carries a larger figure in mechanical horsepower than in metric.
When checking a power conversion, convert to watts first, because every unit in this dimension is defined against the watt and the intermediate value makes the comparison obvious. The trap is comparing a horsepower figure with a kilowatt figure without establishing which horsepower was quoted.
Tanzania reference points
Real quantities, converted into the units on this page.
Tanzania's installed electricity generation capacity
2,881.332 MW = 3,917,521.273829 PS
EWURA reports 2,842.96 MW on the main grid and 38.372 MW off-grid, with TANESCO holding 92.31% of it. Installed capacity is what the country could generate at once, not what it generates on an average day.
Source: EWURA Fact Sheet — electricity sub-sector (installed capacity) · verified 2026-09-14
Related conversions
More power conversions you can convert instantly.
Related calculators
Try these calculators that use power measurements.