Feet to Inches Converter
Convert Feet (ft) to Inches (in) instantly, or use the conversion table below to look up common values.
Feet to Inches conversion table
| Feet (ft) | Inches (in) |
|---|---|
| 1 | 12 |
| 2 | 24 |
| 3 | 36 |
| 4 | 48 |
| 5 | 60 |
| 10 | 120 |
| 25 | 300 |
| 50 | 600 |
| 100 | 1,200 |
How to convert Feet to Inches
1 ft equals 12 in. Use the converter above for any value, or read the table for common conversions.
in = ft × 12.000000000000002 · ft = in × 0.08333333333333333Multiply a feet figure by 12 to get inches, or divide it by 0.083333 to go the other way.
Worked examples
- 1 ft= 12 in
- 5 ft= 60 in
- 10 ft= 120 in
- 25 ft= 300 in
- 100 ft= 1,200 in
What these units are
Feet (ft). A foot is exactly 0.3048 meters, or 12 inches. It is used for height, altitude in aviation and room dimensions wherever imperial measurements are standard.
Inches (in). An inch is exactly 2.54 centimeters. It remains the standard unit for screen sizes, pipe and hose diameters, and tool sizes in imperial-measure countries.
Metric-to-metric conversions are exact. Imperial figures are exact by definition but are rounded for display, so a value converted back and forth can differ in the final digit.
Converting Feet to Inches in practice
Working in feet
The foot is exactly 0.3048 meters, or twelve inches. United States survey work has used a separate survey foot, defined as 1200/3937 meters and equal to about 0.3048006 meters.
Aviation uses feet for altitude and flight levels worldwide, even in countries that measure road distance in kilometers. Building heights, room dimensions, timber and, in some places, body height are also quoted in feet.
The metric conversion is exact, since the foot is defined as 0.3048 meters, and the reverse is exact too. A displayed result is rounded to six decimal places at most, so a round trip can differ in the final digit.
The common slip is assuming a foot is close to a third of a meter when it is slightly longer, so rough mental division undershoots. Feet also belong to length, while square feet measure area and cubic feet measure volume.
The foot competes with the meter for height and building dimensions and with the inch for small spans. Because one meter is a little over three feet, treating a meter figure as feet overstates a dimension more than threefold.
Reading the result in inches
An inch is exactly 2.54 centimeters, or 25.4 millimeters. Twelve inches make one foot and thirty-six make a yard, so the inch sits inside two larger imperial units.
Screen and tyre sizes are given in inches, as are pipe and hose diameters, wrench openings and the diagonal of a television. Rainfall is still recorded in inches in some countries.
Because the inch has an exact metric value, converting to millimeters or centimeters introduces no error beyond display rounding. This site shows at most six decimal places, so very small fractions may appear shortened.
A frequent mistake is reading a pipe size as an exact outside diameter when trade sizes are nominal. Another is converting inches to centimeters and then labelling the answer millimeters.
People confuse inches with centimeters most often of all, then with feet. Screen and pipe sizes are inches, while fabric and body measurements may be either, and a twelvefold confusion between inches and feet is the usual consequence of misreading a unit label in practice.
Checking a feet to inches conversion
Inside the metric units every length conversion is a shift of the decimal point, so millimeters to centimeters, meters to kilometers and the rest can be done by moving it. Which way, and how far, follows from the prefix alone.
Converting between metric and imperial is not a shift but a single exact multiplication, and the factor is the same one for that pair however large or small the value. The trap is mixing the two systems halfway, as when a distance is stated in meters and inches in the same sentence.
To check a length conversion, run it backwards, or convert through a familiar middle value such as a meter or a foot. The one thing to keep straight is pairs that differ by a thousand rather than by ten, since those are where a misplaced decimal point survives unnoticed.
Tanzania reference points
Real quantities, converted into the units on this page.
Uhuru Peak on Mount Kilimanjaro, the highest point in Africa
5,895 m = 19,340.551181 ft = 232,086.614173 in
The datasheet also records Kilimanjaro as rising 4,877 m above the surrounding plains.
Source: UNEP-WCMC World Heritage datasheet — Kilimanjaro National Park · verified 2026-09-14
Marangu Gate, the main road entrance to Kilimanjaro National Park
1,830 m = 6,003.937008 ft = 72,047.244094 in
Source: UNEP-WCMC World Heritage datasheet — Kilimanjaro National Park · verified 2026-09-14
How far Mount Kilimanjaro rises above the plains around it
4,877 m = 16,000.656168 ft = 192,007.874016 in
Source: UNEP-WCMC World Heritage datasheet — Kilimanjaro National Park · verified 2026-09-14
Related conversions
More length conversions you can convert instantly.
Related calculators
Try these calculators that use length measurements.